S197 Mustang parts
81 matching parts guides.
Filter guides1 active
S197 Mustang GT Clutch Slave Cylinder / Hydraulic Throwout Bearing
S197 Mustang GT 2005-10 manual / TR3650
View guideS197 Mustang GT TR3650 Clutch Kit & Flywheel
S197 Mustang GT 2005-10 manual / TR3650
View guide2005-2010 S197 Hydraulic Steering Rack & Inner Tie Rods
S197 Mustang 2005-2010 hydraulic power steering; 2011-2014 EPAS excluded
View guideS197 Front Lower Control Arms & Ball Joints
S197 Mustang 2005-14
View guideS197 8.8 Rear Axle Bearings, Seals & ABS/Tone Ring Parts
S197 Mustang 2005-14 solid axle
View guide4.6 3V Cam Phaser, VCT Solenoid & Timing Service Parts
S197 Mustang GT 2005-10 4.6L 3V
View guide2005-2009 S197 Mustang GT FPDM & Drop-In Fuel Pump Modules
S197 Mustang GT 2005-2009 4.6L 3V; 2010 and non-GT applications require separate verification
View guideS197 Panhard Bar, Brace & Axle-Centering Parts
S197 Mustang 2005-14 solid axle
View guideS197 Cooling-System Diagnosis, Fan & Radiator Paths
S197 Mustang GT 2005-10 4.6L 3V
View guideS197 Door Panel Inserts, Sag Repair & Replacement Cover Paths
2005-2009 S197
View guide2005-2010 S197 Mustang Manual Shifter Linkage Bushings
2005-2010 S197 Mustang with manual transmission; 2011-2014 MT82 excluded
View guideS197 Rear Lower Control Arms, Relocation Brackets & Bent Axle-Bracket Trap
2005-2014 S197
View guideS197 Strut Mounts, Sway Bar End Links & Front-End Clunk Parts
S197 Mustang 2005-2014 - strut/mount combination and trim must be matched; front end links broadly fit 2005-2014
View guide2005-2009 S197 Mustang Front-Door Window Regulators, Motors & Lock Actuators
S197 Mustang 2005-2009 front doors; convertible quarter windows and 2010-2014 regulators excluded
View guide2005-2008 Mustang GT 4.6L 3V Spark Plugs, Coil Boots and Broken-Plug Tooling
2005-2008 Mustang GT 4.6L 3V; Ford broken-plug procedure applies to affected engines built before 2007-11-30
View guide2011-2014 Mustang GT 5.0L Water Pump, Thermostat and Cooling Leak Paths
2011-2014 Mustang GT 5.0L Coyote only; Boss 302, V6 and GT500 excluded unless VIN catalog confirms the exact component
View guide2011-2014 Mustang MT82 Clutch, Flywheel and Hydraulic Release Parts
2011-2014 Mustang 3.7L V6 and 5.0L GT with MT82; engine-specific clutch, flywheel and hydraulic release paths
View guide2011-2014 Mustang MT82 Shift-Quality Diagnosis, Fluid, Pedal and Shifter Support Parts
2011-2014 Mustang V6/GT/Boss with MT82; GT500/TR6060 and automatic excluded
View guide2005-2014 Mustang Front Wheel Hubs, Bearings and ABS Sensor Checks
2005-2014 Mustang front hubs; Ford Performance M-1104-A explicitly supports V6, Boss, GT and Shelby GT500
View guideS197 Mustang Brake Package Guide: V6, GT, GT500, Boss and Factory Brembo Service Parts
2005-2014 S197 brake-package identification; V6, GT, GT500, Boss and factory Brembo paths kept separate
View guide2011-2014 Mustang Two-Piece Driveshaft Diagnosis and One-Piece Conversion Fitment
2011-2014 Mustang 3.7L V6 and 5.0L GT/Boss; exact engine/transmission driveshaft paths; GT500 excluded
View guideS197 Mustang 8.8 Differential Gears, Install Kits, Carrier and Pinion-Flange Fitment
2005-2014 Mustang V8 with 8.8 rear axle and 2011-2014 V6 with 8.8; 2005-2010 V6 7.5 and 2013-2014 GT500 excluded
View guideS197 Mustang Fuel-Level Senders, Saddle-Tank Transfer and Pump-Side Diagnosis
2005-2014 Mustang saddle fuel tank; year- and side-specific pump/sender/jet-pump paths
View guideS197 Mustang EVAP Purge Valve, Vent Solenoid, Canister and Filler-System Diagnosis
2005-2014 Mustang EVAP; purge, vent, canister and filler architecture split by year/engine/body configuration
View guideS197 Mustang Electronic Throttle Body and Accelerator-Pedal Diagnosis
2005-2014 Mustang electronic throttle control; engine- and year-specific throttle body/pedal circuit diagnosis
View guide2011-2014 Mustang Rear Upper Control Arm, Mount and Differential Bushing Fitment
2011-2014 Mustang rear upper control arm, chassis mount and axle/differential bushing; 2005-2010 hardware excluded
View guide2005-2010 Mustang V6 4.0L Thermostat Housing, Thermostat, Water Pump and Leak Paths
2005-2010 Mustang V6 4.0L only; 4.6L/5.4L and 2011-up engines excluded
View guideS197 Mustang Headlight Assemblies, HID/Halogen Components and Model-Year Conversion Traps
2005-2014 Mustang headlamps split 2005-2009, 2010-2012 and 2013-2014; halogen/HID and trim/package distinctions
View guideS197 Mustang Tail Lamps, Sequential Electronics, Harnesses and 2005-2014 Style Splits
2005-2014 Mustang tail lamps split 2005-2009 incandescent, 2010-2012 LED/sequential and 2013-2014 revised LED/sequential systems
View guide2005-2009 Mustang Cowl Water Intrusion, Drain, Grommet and Junction-Box Damage Paths
2005-2009 Mustang front-floor water intrusion; Ford TSB 08-26-7 scope
View guide2005-2010 Mustang GT 4.6L 3V Intake Manifold and Replacement Limits
2005-2010 Mustang GT and 2008-2009 Bullitt with 4.6L 3-valve engine. V6, GT500 and 2011-up 5.0L are excluded.
View guide2011-2014 Mustang EPAS Steering Rack and Programming Fitment
2011-2014 Mustang with factory electric power-assisted steering. Rack calibration and wheel/tire configuration matter; 2005-2010 hydraulic steering is excluded.
View guide2005-2010 Mustang 5R55S Valve Body and Solenoid-Block Diagnosis
2005-2010 Mustang equipped with the 5R55S automatic transmission. 2009-up valve-body casting changes require transmission/build confirmation.
View guide2011-2014 Mustang 6R80 Molded Lead Frame and Valve-Body Diagnosis
2011-2014 Mustang with 6R80 automatic transmission. Recall/customer-satisfaction eligibility is VIN and build-date specific and is not assumed for every car.
View guideS197 Mustang Clutch Master Cylinder, Pedal and Hydraulic Line
2005-2014 Mustang with manual transmission. Master-cylinder design splits at 2011; engine/transmission and GT500 hardware still require VIN confirmation.
View guideS197 Mustang HVAC Blend-Door and Mode-Door Actuators
2005-2014 Mustang HVAC air-distribution system. Door position, production period and manual versus automatic climate equipment determine the actuator.
View guideS197 Mustang Blower Motor, Resistor and Speed Controller
2005-2014 Mustang blower system. Manual stepped-resistor and automatic/variable-speed controller applications differ, with a 2010-era transition requiring VIN/equipment confirmation.
View guideS197 Mustang A/C Compressor, Clutch and Condenser Fitment
2005-2014 Mustang A/C system across 4.0L, 3.7L, 4.6L, 5.0L, 5.4L and 5.8L applications. Engine, model year and compressor configuration are mandatory.
View guideS197 Mustang Oxygen Sensors and Catalytic Converters by Application
2005-2014 Mustang oxygen-sensor and catalyst systems. Engine, bank, upstream/downstream position, transmission and emissions certification determine the part.
View guideS197 Mustang Axle Vent, Differential Cover and Pinion-Seal Leaks
2005-2014 Mustang solid rear axle. Confirm 7.5-inch versus 8.8-inch axle, ratio/differential, production and special-model exclusions before buying cover or service parts.
View guideS197 Mustang Convertible-Top Hydraulic Pump, Cylinders and Lines
2005-2014 Mustang convertible only. Hydraulic-cylinder fitment includes a production split around 2007-08-20; coupe and unrelated top/fabric parts are excluded.
View guide2011-2014 Mustang GT 5.0L VCT Solenoids and Cam-Timing Diagnosis
2011-2014 Mustang GT/Boss 302 with first-generation 5.0L Coyote. 4.6L 3V, V6, GT500 and 2015-up Coyote diagnostics are excluded.
View guideS197 Mustang Exterior Mirrors, Glass, Heat and Pony-Lamp Options
US-market 2005-2014 S197 Mustang exterior door mirrors. Service eras are 2005-2009, 2010, 2011-2012, and feature-sensitive 2013-2014; left/right and original equipment must match. No cross-era interchange is asserted.
View guideS197 Mustang GT/V6 Strut, Shock and Spring Package Selection
US-market 2005-2014 S197 Mustang GT and V6 factory-style damper/spring service, split by engine, body, year and suspension package. Boss 302, Shelby/GT500, Bullitt and other special suspension packages are excluded unless separately verified.
View guide2005-2014 S197 Mustang Wiper Motor, Linkage, Arms and Park Diagnosis
US-market 2005-2014 S197 Mustang front windshield-wiper mechanism, split into 2005-2007 and 2008-2014 motor/linkage service families. Arms remain side-, suffix-, production- and equipment-sensitive. Cowl-water diagnosis and TSB 08-26-7 remain in S197-0031.
View guide2011-2014 Mustang 3.7L V6 Starter Motor and No-Crank Diagnosis
US/LHD 2011-2014 S197 Ford Mustang with the 3.7L V6, manual or automatic transmission. The 2005-2010 cars, 5.0L, 5.4L and 5.8L engines, other applications and powertrain swaps are excluded.
View guide2005-2009 Mustang GT Standard Front Fascia: Cover, Grilles, Fog Lamps and Energy Absorbers
US/LHD 2005-2009 S197 Mustang GT Deluxe/Premium Coupe and Convertible with the factory standard 4.6L V8 front fascia; V6/Pony Package, GT California Special, Shelby GT/GT500, Bullitt, Mustang Sally, Roush, Saleen, aftermarket and conversion fascias are excluded; 2010-2014 and later cars are excluded.
View guide2011-2014 Mustang 3.7L V6 Engine Mount Insulators: Automatic vs Manual
US/LHD 2011-2014 S197 Ford Mustang with the factory 3.7L V6 and either 6R80 six-speed automatic or MT82 six-speed manual. 2005-2010 4.0L V6/4.6L GT, 2011-2014 5.0L GT/Boss, 5.4L/5.8L GT500, 2015-plus, swaps, solid/race mounts, transmission-mount-only work and non-US/RHD applications are excluded.
View guide2011-2014 Mustang GT 5.0L Main and A/C Belts, Tensioner and Idler Pulley
US/LHD 2011-2014 S197 Ford Mustang GT with the factory naturally aspirated 5.0L Coyote V8. Boss 302, GT500, every V6, 2005-2010 GT, 2015-plus, supercharger systems, accessory-drive conversions, engine swaps and universal belt/pulley claims are excluded.
View guide2005-2010 Mustang GT 8.8 Rear Axle Assembly, Housing and Used-Donor Identification
US/LHD 2005-2010 S197 Ford Mustang GT with the factory 4.6L 3V V8 and factory 8.8-inch solid rear axle. Standard GT Coupe or Convertible only after VIN, build, axle tag and installed configuration agree. Every 4.0L Base/V6 7.5-inch axle, GT500, GT500KR, Bullitt and other Shelby or special-edition branches, 2011-plus assemblies, non-US cars, swaps, fabricated or 9-inch housings, internal rebuild work, axle-shaft-only work and suspension-link work are excluded.
View guide2010-2012 Mustang GT Rear Bumper Cover, Lower Valance, Supports and Equipment Branches
US/LHD 2010-2012 S197 Ford Mustang GT Coupe or Convertible: 2010 factory 4.6L V8 and 2011-2012 factory 5.0L V8. The outer rear cover is shared across checked trims, but the lower valance and supports vary by build date, GT appearance package, Boss/Shelby configuration and reverse-proximity-sensor equipment. Base/V6 selection, GT500, Boss 302, GT California Special/appearance-package conversion claims, 2005-2009, 2013-2014 and later cars, deck-lid trim/emblems, lamps/reflectors, structural repair and aftermarket body kits are excluded except where an excluded factory branch is shown solely to prevent a misorder.
View guide2005-2010 Mustang GT 4.6L Starter Motors: Production Split, Mounting and No-Crank Diagnosis
US/LHD 2005-2010 S197 Ford Mustang GT Coupe or Convertible with the factory naturally aspirated 4.6L three-valve V8 and either the TR3650 five-speed manual or 5R55S five-speed automatic. Installed starter identity changes around December 2005, but the checked Ford reman service replacement covers both transmissions; manual clutch-interlock and automatic range-sensor logic remain separate diagnostic branches. Exclude the 4.0L V6, 2011-up 3.7L/5.0L, GT500 5.4L, swaps, generic modular-engine fitment and any PATS or safety-interlock bypass.
View guide2011-2014 Mustang GT 5.0L Production Fuel-Pump Module, FPCM and Pressure/No-Start Diagnosis
US/LHD 2011-2014 S197 Ford Mustang GT Coupe or Convertible with the factory naturally aspirated 5.0L four-valve V8 and production Mechanical Returnless Fuel System (MRFS). This page is limited to the LH primary fuel-pump module, the single production Fuel Pump Control Module (FPCM/FPDM search language), pressure/no-start diagnosis, electrical connectors and pump-opening seals. Exclude 3.7L V6, Boss 302, Shelby GT500 5.4L/5.8L, 2005-2010 cars, 2015-up cars, swaps, forced-induction conversions, return-style conversions, dual-pump systems and performance upgrades. Fuel-level sender and saddle-tank transfer selection is expressly out of scope and remains with canonical S197-0024.
View guide2010-2014 Mustang Front-Door Window Regulators, Motors and Short-Drop Diagnosis
US/LHD 2010-2014 Ford Mustang Coupe and Convertible front-door power-window systems only. This guide separates RH/passenger from LH/driver regulators, seven-pin smart motors, switch position, door-ajar input, short-drop initialization and body-specific front glass. 2005-2009, rear-quarter windows, 2015-up S550, non-US/RHD cars, universal conversions and unsupported Coupe/Convertible glass interchange are excluded.
View guide2010-2014 Mustang GT Standard Front Fascia: Cover, Grilles, Fog Lamps and Supports
US/LHD 2010-2014 Ford Mustang GT Coupe and Convertible standard factory front fascia only, separated into 2010-2012 and 2013-2014 refresh branches. The outer bumper cover, upper grille, lower grille or valance, fog lamps, grille surround, absorber, brackets and reinforcement are treated as separate identities. V6, GT/CS, Boss 302, Shelby GT500, appearance/performance or other special-package fascia, non-US/RHD cars, aftermarket aero and unsupported conversions are excluded.
View guide2010-2014 S197 Mustang Instrument-Cluster Assembly Identification
US/LHD 2010-2014 Ford Mustang factory instrument-panel clusters (IPC) only, split by 2010, 2011, 2012 and 2013-2014 application evidence and then by exact VIN/build date, engine and trim (V6, GT, Boss 302 or Shelby GT500), 2010-2012 four-gauge versus optional six-gauge equipment, 2013-2014 base message-center versus optional LCD/unique-feature configuration, MPH-primary scale, transmission/display content and installed service/engineering label. 2005-2009 and 2015-up Mustang, non-US/RHD or KMH-primary assumptions, race-only R-Package parts, aftermarket digital conversions, security bypass/emulator devices, EEPROM work, mileage alteration and unsupported cross-year/cross-trim interchange are excluded.
View guide2005-2014 Mustang Factory Aluminum Hoods: Three Exterior Eras, Scoop/Vent, Latch and Insulator Branches
US/LHD 2005-2014 Ford Mustang factory S197 hood applications only, divided first into the non-interchangeable 2005-2009, 2010-2012 and 2013-2014 exterior eras and then by exact VIN, build date, Base/V6, GT, Bullitt, Boss 302 or Shelby/GT500 factory equipment and installed scoop, vent, stripe and insulation provisions. Exclude 2015-up S550, non-US/RHD applications, aftermarket carbon/fiberglass panels, unsupported cross-era or trim conversions, and vehicles with unmeasured collision damage at the hinge, latch, upper tie-bar, fender or headlamp interfaces.
View guide2005-2009 Mustang Factory Rear Fascias: V6, GT, GT/CS, GT500 and Supports
US/LHD 2005-2009 Ford Mustang factory rear fascia applications only. Resolve the recipient VIN, model year, build date, original trim and appearance package, installed cover identity, exhaust outlets and Coupe or Convertible body before ordering. Proven cover branches are Base/V6 and standard GT for 2005-2009, plus the checked 2007-2009 GT California Special/Shelby GT appearance branch and the distinct 2007-2009 Shelby GT500 branch. The checked Ford mounting-bracket catalog lists Coupe and Convertible together rather than creating separate cover or bracket identities; adjacent rear body, floor and quarter structure can still differ and is outside this guide. Exclude 2010-up body shapes, non-US/RHD assumptions, Bullitt or other special-edition identity unless the VIN and installed Ford number resolve it, GT500/GT/CS appearance conversions on another trim, Saleen/Roush/aftermarket fascias, fabricated diffuser or exhaust conversions and unmeasured structural collision repair.
View guide2005-2014 Mustang Factory Wheels and TPMS: Package, Stagger and Brake-Clearance Identification
US/LHD 2005-2014 Ford Mustang S197 factory road wheels and matching factory TPMS service paths only. Resolve recipient VIN, model year, V6/GT/Bullitt/Boss/Shelby equipment, factory brake package, front versus rear position, wheel casting or service identity, measured diameter/width/offset/backspacing and hub-pilot fit before ordering. Exclude 2015-up S550, replica or generic aftermarket-wheel identity claims, tires presented as wheel-fitment proof, drag or race-wheel selection, unsupported cross-era/cross-trim interchange and any wheel whose load, structural repair or runout cannot be documented.
View guide2005-2010 Mustang GT and Bullitt TR3650 Manual Transmission Assembly Identification
US/LHD 2005-2010 Ford Mustang GT and 2008-2009 Bullitt with the factory 4.6L three-valve V8, five-speed manual and Ford certification-label transmission code K only. Resolve recipient and donor VIN/build, the complete transmission tag or engineering marks, S197 case and integrated clutch-housing identity, stock or converted input, rear output flange, remote-shifter equipment, speed-sensing and reverse-switch interfaces, mount and itemized sale contents before ordering. Exclude 2005-2010 V6 T5, 2007-2010 Shelby GT500 TR6060, 2011-up MT82, automatics, 2001-2004 cable-clutch/slip-yoke TR3650 units, non-US/RHD assumptions, Shelby GT or other special-package assumptions outside this page, 26-spline/performance conversions and unsupported cross-platform swaps.
View guideS197 Mustang Front Door Shells: 2005-2009 versus 2010-2014, Side and Bare-versus-Loaded Identification
US/LHD 2005-2014 Ford Mustang S197 factory front-door shells only, separated first into 2005-2009 and 2010-2014 service eras and then into left/driver versus right/passenger side. The checked Ford diagrams apply each era's shell pair to both Coupe and Convertible; body style is not represented as a separate bare-shell identity in this evidence. A loaded donor still requires Coupe/Convertible and equipment confirmation for every attached component. Exclude 2015-up S550, non-US/RHD assumptions, rear-quarter structure, outer skins presented as shells, cross-era appearance conversions, modified or cut doors and vehicles with unmeasured A-pillar, rocker or latch-pillar collision damage.
View guide2011-2014 Mustang GT and 2012-2013 Boss 302 5.0L Engine and Long-Block Donor Identification
US/LHD 2011-2014 Ford Mustang GT and 2012-2013 Mustang Boss 302 factory 5.0-liter engine/service-engine or defined long-block replacement paths only. Resolve recipient VIN/build, GT versus Boss 302, model year, exact engine tag/service identity, GT automatic 6R80 versus manual MT82 preparation, Boss production MT82 manual-only configuration, oil-pan/oil-cooler configuration, front cover, VCT connectors, intake/exhaust, sensors, harness, PCM/calibration, flywheel/flexplate, accessories and every included component. Exclude 2005-2010 4.6L, 3.7L V6, Shelby GT500, 2015-up S550, F-150/truck or SUV 5.0L assumptions, Boss 302S race packages presented as production-road-car equivalents, non-US/RHD applications, modified crate/performance builds and unsupported swaps.
View guide2011-2014 Mustang Standard V6 and GT 8.8 Rear Axle Housings and Complete-Donor Identification
US/LHD 2011-2014 Ford Mustang S197 factory 8.8-inch solid-rear-axle applications limited to standard Base/V6 3.7L and GT 5.0L cars described by the checked Ford service catalog as less optional equipment pack and less special equipment package. Resolve recipient and donor 17-character VINs, production, Safety Compliance Certification Label AXLE code, metal housing tag, exact ratio, differential type, flange, ABS, brake and suspension interfaces and written contents. Exclude Boss 302, Laguna Seca, Shelby GT500, Torsen/Track/Performance/special-equipment packages, 2005-2010, 2015-up IRS, Cobra Jet/race or fabricated housings, unidentified mixed assemblies and structural-repair claims.
View guide2005-2014 Mustang Factory Front Subframes: K-Member Identity, Interfaces and Condition
US/LHD 2005-2014 Ford Mustang S197 factory front subframe/K-member, Ford base 5C145. Resolve recipient and donor VINs/builds, exact stamped or current service identity, bare versus loaded contents, hydraulic 2005-2010 versus EPAS 2011-2014 steering equipment, engine and insulator/bracket interfaces, control arms/cam hardware, lower/front crossmembers and braces, body style/support braces, geometry, collision/corrosion condition and freight terms. Exclude 2015-up S550/S650, non-US/RHD assumptions, tubular drag/drift members, rack-relocated or engine-swap pieces, cut/welded members and structural-repair claims.
View guide2005-2014 Mustang ABS HCU, Pump and Electronic Module Identification
US/LHD 2005-2014 Ford Mustang factory four-wheel-ABS hydraulic control units and electronic controllers only. Resolve recipient and donor VINs/builds, original ABS equipment, 2005-2009 ABS/traction-control versus 2010-2014 AdvanceTrac generation, Base/V6/GT versus Shelby branches, the 2010 and 2011 production breaks, exact installed/service numbers, connector and six brake-line ports, configuration and written contents. Exclude non-ABS cars, S550, non-US/RHD assumptions, unidentified universal units, flood/fire/collision-contaminated donors, race-only controllers and ABS/traction/stability delete or bypass work.
View guide2005-2014 Mustang Steering Columns and Intermediate Shafts: Core Identity, Safety and Contents
US/LHD 2005-2014 Ford Mustang factory manual-tilt steering column assemblies, upper steering shafts and lower shaft/coupling assemblies. Resolve recipient and donor VIN/build, exact installed/service identity, model-year equipment, Coupe/Convertible donor record, hydraulic-rack versus EPAS lower interface, transmission/interlock provisions, tilt, brackets, splines/joints, lawful ignition/lock equipment and written contents. The checked catalogs support one 3C529 column core and common upper/lower shaft service families across 2005-2014; they do not prove that every attached trim, lock, switch, clockspring, rotation sensor, harness or fastener is universal. Exclude S550, non-US/RHD, race or quick-release columns, theft/immobilizer or restraint bypass, cut/welded/altered shafts and any impact-collapsed or deployment donor.
View guide2005-2014 Ford Mustang S197 Factory Saddle Fuel-Tank Shell Identification
US/LHD 2005-2014 Ford Mustang S197 factory saddle fuel-tank shells only. Resolve recipient and donor VIN/build, Coupe/Convertible, production, 4.0/3.7/4.6/5.0/5.4/5.8 engine and Base/V6/GT/Boss/Shelby equipment, emissions certification, early capped versus later capless filler architecture, exact installed/service identity, pump/sender apertures, internal transfer, EVAP/vent interfaces and written contents. GT500 manual-only vehicle scope does not make its tank universal. Exclude S550/S650, non-US/RHD, racing cells, return-style/performance conversions, modified shells and unqualified repair, cleaning, purging or hazardous shipping claims.
View guide2005-2014 Ford Mustang S197 Radiator/Core-Support and Front-Body Carrier Identification
US/LHD 2005-2014 Ford Mustang S197 factory radiator/core-support panel and its upper/side support pieces only. Resolve recipient VIN/build, 2005-2009 versus 2010-2014 complete-panel branch, Coupe/Convertible body, engine/trim, cooling package and installed front fascia, headlamp, hood-latch, fender, bumper and air-guide interfaces. Exclude S550/S650 and non-US/RHD assumptions; radiator/fan diagnosis owned by S197-0009, headlamps by S197-0029, fascia by S197-0048/S197-0056, hood/latch-adjacent equipment by S197-0058 and lower K-member by S197-0065; radiators, condensers, fans, coolers, impact bars/isolators, aprons/rails, cut clips and unqualified pull/weld/sectioning claims.
View guide2005-2014 Ford Mustang S197 Factory Automatic-Transmission Assembly Identification
US/LHD factory-production S197 Mustang automatic branches only: 2005-2010 4.0L V6 and 4.6L GT with 5R55S, plus 2011-2014 3.7L V6 and 5.0L GT with 6R80. The 2014 V6 branch splits at 2014-06-27 production. Exclude manual transmissions, GT500/Boss, 2015-up Mustangs, truck/SUV 6R80 units, non-US/RHD cars and swaps.
View guide2005-2014 Ford Mustang S197 Convertible Soft-Top Frames: Production Branches, Bare Frame and Complete-Donor Contents
US/LHD 2005-2014 Ford Mustang S197 factory Convertible soft-top structure only: complete Ford top assemblies where the exact cover is part of the identity, bare frame assemblies where the cover is expressly excluded, and separately cataloged bows, side rails, header/front panel, clamps and hinge pins. Resolve recipient and donor VIN/build, Convertible body, production branch, exact identity, cover material/color where applicable, actual donor contents and condition. Exclude Coupe, non-US/RHD assumptions, 2015-up S550, universal/manual conversions, unsupported year collapsing, and any claim that a fabric-and-glass replacement top is a structural frame.
View guide2005-2010 Ford Mustang S197 4.0L V6 Engines and Long Blocks: Transmission, Balance-Shaft and Written-Contents Identification
US/LHD 2005-2010 Ford Mustang S197 with the factory VIN-N 4.0L SOHC V6 only. Resolve recipient and donor 17-character VINs, build dates, original engine/service tag, installed or service identity, automatic versus manual preparation, balance-shaft branch, oil-pan/pickup and written included equipment. Exclude 4.6L, 5.0L and 5.4L engines, 2011-up Mustangs, truck/SUV shared-family assumptions, imported/non-US or RHD applications, swaps and incomplete, overheated, oil-starved, hydrolocked, flooded, fire-exposed or undocumented modified engines.
View guide2005-2014 Ford Mustang S197 Factory Axle-Back Mufflers and Over-Axle Pipe Identification
US/LHD 2005-2014 Ford Mustang S197 factory rear axle-back muffler/tailpipe assemblies and separately inventoried over-axle or rear pipes only. Resolve recipient and donor 17-character VINs, build dates, 2005-2010 versus 2011-2014 body generation, engine, transmission, Coupe/Fastback or Convertible where applicable, special model, left/right side, tip treatment, rear-fascia opening, pipe/clamp diameter, hanger geometry and written contents. Exclude 2015-up, non-US/RHD assumptions, manifolds, catalytic converters, oxygen sensors, upstream H/X or mid-pipes as the primary decision, universal systems, emissions deletes, unsupported V6/GT/Boss/GT500 interchange and cut, perforated, crushed, collision-damaged or undocumented modified assemblies.
View guideUS S197 Mustang Factory Trunk/Deck Lid, Audio/Spoiler Branch and Written-Contents Identification
US/LHD 2005-2014 Ford Mustang S197 factory trunk/deck-lid donors, researched through checked 2005-2009 and 2013-2014 service examples. Prove both VINs/builds, exterior era and year, Coupe/Convertible application, analog versus satellite-audio antenna treatment, spoiler state, lid identity, hinges/lifts, latch/lock/emblem/trim/wiring and written contents. Exact 2010-2012 lid identity remains VIN-catalog gated. Exclude 1994-2004 and 2015-up, universal spoilers, cut antenna or camera modifications and bent, corroded, collision-, fire- or flood-damaged donors.
View guideUS/LHD S197 Mustang Factory Dashboard/Instrument Panel and Written-Contents Identification
US/LHD Ford Mustang S197 factory upper instrument-panel/dashboard donors, narrowed to the checked 2007-2009 color/package branches and the checked 2014 charcoal-black branch. Prove recipient and donor VIN/build, exact production date, interior color and decor package, Coupe or Convertible interfaces, upper pad identity, reinforcement/carrier, ducts/vents, glove/cluster/knee/center trim, passenger-airbag state, harness paths, condition and written contents. Exclude blanket 2005-2014 interchange, 2015-up S550, non-US/RHD assumptions, custom-cut panels and cracked, warped, collision-, fire- or flood-damaged donors.
View guideUS/LHD S197 Mustang Front-Seat Track, Frame, Airbag/Occupancy Interface and Written-Contents Identification
US/LHD 2005-2014 Ford Mustang S197 factory front-seat donors and separately identified track/frame components only. Prove both VINs/builds, production/interior era, Coupe or Convertible interfaces, left/driver versus right/passenger side, standard/sport/Recaro family, manual/power adjustment, trim/heating, side-airbag and passenger-occupancy equipment, buckle/interface, labels, condition and written contents. Exclude 2015-up, universal/racing seats, fabricated brackets, SRS/occupancy emulators and bent, welded, seized, crash-loaded, fire-, flood- or biohazard-contaminated donors.
View guideUS/LHD S197 Mustang Coupe and Convertible Rear-Seat Cushion/Backrest and Written-Contents Identification
US/LHD 2005-2014 Ford Mustang S197 factory rear-seat cushion and backrest donors only, separated by Coupe or Convertible body, 2005-2009 versus 2010-2014 interior era, upholstery/package and folding/latch geometry. Prove both VINs/builds, body, production, trim/color, cushion and backrest pads/frames/covers, Coupe folding hinges/latches or Convertible fixed-panel geometry, head restraints where equipped, belt/buckle openings, condition and written contents. Exclude front/racing seats, rear-seat deletes, 2015-up, non-US/RHD assumptions, fabricated mounts and crash-loaded, fire-, flood-, mold-, pest-, smoke- or biohazard-contaminated donors.
View guideUS/LHD S197 Mustang 2005-2009 and 2010-2014 Molded Floor-Carpet and Backing Identification
US/LHD 2005-2014 Ford Mustang S197 factory molded floor carpet or checked era-specific replacement carpet kits only, separated into 2005-2009 and 2010-2014 interiors and verified for Coupe/Convertible application, trim/color and equipment openings. Prove recipient production, body, factory identity or seller application, tunnel/console/seat/belt openings, backing/padding, color, condition and written contents. Exclude floor mats represented as molded carpet, 2015-up, non-US/RHD assumptions, structural floor repair and cut, wet, moldy, burned, pest-, smoke- or biohazard-contaminated donors.
View guideUS/LHD S197 Mustang Center-Console, Shifter-Trim and Equipment Identification
US/LHD 2005-2014 Ford Mustang S197 factory floor center-console shells, shifter finish panels/bezels and parking-brake/armrest trim only, narrowed into 2005-2009 versus 2010-2014 interior eras, Coupe/Convertible body, manual/automatic transmission, lighting/equipment and color branches. Prove both VINs/builds, production/interior era, body, transmission, exact identity, color, cupholder/lighting/switch layout, mounting geometry, condition and written contents. Exclude mechanical shifter internals, dashboard, carpet, 2015-up, early/late interchange without exact proof and cracked, cut, melted, warped, water-damaged or heavily repaired donors.
View guideUS/LHD 2005-2014 S197 Mustang Trunk-Carpet, Floor and Side-Trim Identification
US/LHD 2005-2014 Ford Mustang S197 factory luggage-compartment carpet, floor mat/board, side trim and checked spare/inflator/tool covers only, narrowed by 2005-2009 versus 2010-2014 interior era, Coupe/Convertible body, spare/inflator and Shaker/audio layout, physical section, color and fasteners. Prove both VINs/builds, era, body, equipment, molded identity, section count, backing, condition and written contents. Exclude trunk lids, passenger-compartment carpet, 2015-up cars and cut, wet, moldy, burned, pest-, smoke-, flood- or biohazard-contaminated donors.
View guideUS/LHD 2005-2014 S197 Mustang Full Interior Door-Panel and Loaded-Contents Identification
US/LHD 2005-2014 Ford Mustang S197 factory full interior door panels/cards only, narrowed by 2005-2009 versus 2010-2014 interior era, Coupe/Convertible body, physical side, audio/subwoofer, decor/interior package, switch/handle equipment, color and written loaded contents. Prove both VINs/builds, era, body, side, equipment, molded/service identity, every mount, condition and contents. Exclude door shells, window regulators, 2015-up cars and insert-only delamination repair already owned by S197-0010.
View guide2005-2014 Ford Mustang S197 Headliner and Overhead-Trim Identification
2005-2014 Ford Mustang S197 factory Coupe roof-board/headliner and the physically distinct Convertible top headliner, plus checked visors, overhead console/lamp openings and retainers only, narrowed by body, production/interior era, color, lighting/console/visor/garage-opener equipment, physical section and written contents. Prove both VINs/builds and exact body. Coupe and Convertible headliners are not one interchangeable part class. Exclude convertible-top frame, bows, latches, hydraulics and weatherseals owned by S197-0071, plus roof sheet metal, airbags, harnesses and moldy, wet, smoke-, fire- or pest-damaged donors.
View guide