Parts/350Z/G35
350Z/G35 · Buyer's guide

2003-2009 Nissan 350Z Under-Dash Heater, Evaporator and Blower Module Identification

US/LHD Nissan 350Z factory under-dash HVAC modules only: 2003-2008 Coupe and 2004-2009 Roadster, with exact 2009 Roadster VIN/build confirmation. Separate heater/air-mix case, cooling/evaporator case and blower module; resolve body, production, VQ35DE versus VQ35HR, manual versus automatic climate equipment and exact installed/service identity. Exclude Infiniti G35 assumptions, 370Z, non-US/RHD, universal under-dash units and external compressor, clutch, condenser, receiver-drier or line selection retained by Z33-0038.

Current seller options

WHERE TO BUY

Open an exact listing, then confirm fitment, stock, price, and shipping with the seller before ordering.

Disclosure: Supersede participates in the eBay Partner Network and may earn a commission from qualifying purchases. Commission-eligible seller cards are identified below. This does not affect your price, our fitment research, or how sellers are selected.

Seller links checked . Prices and availability can change.

Checking live eBay listing…
eBay
Current priceChecking live listing…
What you need to know

Start with recipient and donor VIN/build, Coupe/Roadster, production, engine and climate-control equipment. Identify the separate blower, evaporator/cooling and heater/air-mix modules rather than treating heater box as one universal assembly. Compare firewall heater tubes and evaporator connections, condensate drain, duct joints, mounting tabs, blower/controller interface, temperature/mode/recirculation doors, actuators, sensors, harnesses and every seal/fastener. Require a written inventory of heater core, evaporator, expansion valve, blower motor/fan, controller/resistor, doors/actuators, sensors, drain, ducts, wiring and hardware. Reject cracked/warped housings, broken tabs, seized doors, kinked tubes, coolant or refrigerant-oil residue, corrosion, flood/fire exposure, mold, rodents, debris, odor or cut wiring. Preserve Z33-0038 external A/C ownership. Follow EPA refrigerant-recovery requirements, work only on a cold/depressurized cooling system and use qualified HVAC service.

OEM numbers

HEATER/AIR-MIX CASE PIECES: 27120-CD000 front case and separate 27321-CD000 cover. LOADED HEATER/COOLING UNIT PATHS: 27110-CD000, 27110-CD00A and 27110-CD00B -> 27110-CD00Clater production also uses separate 27110-CF40A and 27110-CF40C branches, with CF40C shown from 11/2006. BLOWER ASSEMBLY: 27200-CD000 -> 27200-CD00Aseparate blower case 27235-CD000. BLOWER MOTOR WITH CASE: 27225-AM600, 27225-AM610, 27225-AM611 and 27225-AM61A -> 27225-1EA0A. HEATER CORE: 27140-AM60A -> 27140-AM600. EVAPORATOR: 27281-AM600 and 27281-CA000 -> 27281-CB62A. Module, body, production, climate equipment and loaded contents remain separate.

Supersession

Checked service links are 27110-CD000 / 27110-CD00A / 27110-CD00B -> 27110-CD00C; 27200-CD000 -> 27200-CD00A; 27225-AM600 / 27225-AM610 / 27225-AM611 / 27225-AM61A -> 27225-1EA0A; 27140-AM60A -> 27140-AM600; and 27281-AM600 / 27281-CA000 -> 27281-CB62A. Later 27110-CF40A and 27110-CF40C are retained as production branches rather than invented successors. Bare cases, covers, loaded units, blower assemblies, heater cores and evaporators are not interchangeable descriptions.

Fitment

Start with recipient and donor VIN/build, Coupe/Roadster, production, engine and climate-control equipment. Identify the separate blower, evaporator/cooling and heater/air-mix modules rather than treating heater box as one universal assembly. Compare firewall heater tubes and evaporator connections, condensate drain, duct joints, mounting tabs, blower/controller interface, temperature/mode/recirculation doors, actuators, sensors, harnesses and every seal/fastener. Require a written inventory of heater core, evaporator, expansion valve, blower motor/fan, controller/resistor, doors/actuators, sensors, drain, ducts, wiring and hardware. Reject cracked/warped housings, broken tabs, seized doors, kinked tubes, coolant or refrigerant-oil residue, corrosion, flood/fire exposure, mold, rodents, debris, odor or cut wiring. Preserve Z33-0038 external A/C ownership. Follow EPA refrigerant-recovery requirements, work only on a cold/depressurized cooling system and use qualified HVAC service.

Aftermarket options

A direct-replacement blower motor, heater core or evaporator can be considered only after the exact module and interfaces are identified; a component listing is not a complete case. Universal under-dash systems and unsupported whole-case swaps change ducts, controls, drains, wiring, coolant/refrigerant interfaces and crash/SRS-adjacent dash work and are outside this guide. Require lawful refrigerant recovery and current manufacturer procedures.

Before you buy

US/LHD 2003-2008 Coupe and 2004-2009 Roadster only, with 2009 Roadster confirmed by VIN/build. Separate blower, evaporator/cooling and heater/air-mix modules; match production, engine, climate equipment, interfaces and written contents. Reject cracked, contaminated, mold/rodent/flood/fire-exposed or cut-wiring donors. Preserve external A/C ownership, require lawful refrigerant recovery and qualified dash/HVAC service.

Research and fitment sources